Penggunaan Metode Fuzzy Failure Mode and Effect Analysis Pada Hasil Inspeksi Proteksi Katodik PT PGAS Solution Area Bekasi
Keywords:
bekasi, cathodic protection, fuzzy, failure mode and effect analysis, gas pipelineAbstract
Cathodic protection is used to prevent corrosion in gas pipeline networks, so it is necessary to conduct regular inspections to ensure its effectiveness. This research uses the Fuzzy Failure Mode and Effect Analysis (Fuzzy FMEA) method to analyse the results of cathodic protection inspections on the PT PGAS Solution Area Bekasi gas pipeline network, identify the causes of failures, and determine the control actions that can be taken based on the cause of the failure. Data obtained from cathodic protection inspection activities and expert interviews show that the most common failures are those with low potential values. FRPN calculations using the Fuzzy FMEA method show that environmental factors are critical causes of low potential failures. The main cause is an environment with a soil barrier that is too high, so control measures can be taken by adding additional anodes, lowering the soil barrier or replacing the anode with a larger one. It is hoped that the results will become a recommendation for companies to solve the problem of low potential value disturbances in cathodic protection.
References
[1] M. Iswahyudi et al., Manajemen Pemasaran: Strategi dan Praktek yang efektif. Jambi: PT. Sonpedia Publishing Indonesia, 2023.
[2] Nur Sahroni and R. A. Darajatun, “Efektivitas Proses Produksi Melalui Pengendalian Kualitas pada Part End Plate dengan Metode Lean Six Sigma di PT. GCE,” Ind. J. Ilm. Tek. Ind., vol. 8, no. 2, pp. 343–351, 2024, doi: 10.37090/indstrk.v8i2.1259.
[3] Y. Hisprastin and I. Musfiroh, “Ishikawa Diagram dan Failure Mode Effect Analysis (FMEA) sebagai Metode yang Sering Digunakan dalam Manajemen Risiko Mutu di Industri,” Maj. Farmasetika, vol. 6, no. 1, p. 1, 2020, doi: 10.24198/mfarmasetika.v6i1.27106.
[4] I. Tanjung, A. Affandi, S. Huzni, and S. Fonna, “Investigasi pengaruh jumlah elemen anoda terhadap distribusi potensial korosi pada beton bertulang menggunakan BEM 3D,” J. Rekayasa Mater. Manufaktur dan Energi, vol. 3, no. 1, pp. 57–64, 2020, doi: 10.30596/rmme.v3i1.4529.
[5] R. Saputra and D. T. Santoso, “Analisis Kegagalan Proses Produksi Plastik Pada Mesin Cutting Di Pt. Fkp Dengan Pendekatan Failure Mode and Effect Analysis Dan Diagram Pareto,” Barometer, vol. 6, no. 1, pp. 322–327, 2021, doi: 10.35261/barometer.v6i1.4516.
[6] A. Saefullah, A. Fadli, Nuryahati, I. Agustina, and F. Abas, “Implementasi Prinsip Pareto Dan Penentuan Biaya Usaha Seblak Naha Rindu,” J. Media Wahana Ekon., vol. 20, no. 1, pp. 1–13, 2023, doi: 10.31851/jmwe.v20i1.11077.
[7] W. Astutik, Mujaddid, J. Kulsaputro, A. Fole, and N. Yanasim, “Enhancing Risk Mitigation Strategies In Innovative Poultry Slaughterhouses: A House Of Riskmethod Approach,” Sci. Junal Ilm. Sains dan Teknol., vol. 2, no. 11, pp. 1–21, 2024.
[8] Khamaludin, I. Respatiningsih, and B. Kustiawan, Manajemen Mutu. Jambi: Sonpedia Publishing Indonesia, 2024.
[9] M. T. Sembiring, A. R. S. Meliala, and M. Z. Harahap, “Analisis Permasalahan Menggunakan Cause and Effect Diagram , Fault Tree Analysis dan Afinity Diagram,” Talent. Conf. Ser. Energy Eng., vol. 5, no. 2, pp. 163–168, 2022, doi: 10.32734/ee.v5i2.1561.
[10] Intan Putri Ramadhani and Wida Winardini, “Analisis Diagram Fishbone Dalam Kebijakan Pengelolaan Sampah Di Kota Surabaya,” J. Media Akad., vol. 2, no. 5, 2024, doi: 10.62281/v2i5.281.
[11] B. Khrisdamara and D. Andesta, “Analisis Penyebab Kerusakan Head Truck-B44 Menggunakan Metode FMEA dan FTA (Studi Kasus : PT. Bima, Site Pelabuhan Berlian),” J. Serambi Eng., vol. 7, no. 3, 2022, doi: 10.32672/jse.v7i3.4255.
[12] M. D. Farrizqi and D. Andesta, “Analisis Pengendalian Kualitas dengan Menggunakan Metode Failure Mode and Effect Analysis dan Fault Tree Analysis pada Produk Songkok UD. XYZ,” G-Tech J. Teknol. Terap., vol. 8, no. 2, pp. 835–846, 2024, doi: 10.33379/gtech.v8i2.4052.
[13] S. Ramadhania, D. Mubarok, Mislan, A. Rahmatullah, B. Panulisan, and D. Khaerudin, “Quality Control Of Capsule A Products Using Statistical Process Control (SPC) And Fuzzy Failure Mode And Effect Analysis (F-FMEA) Methods At PT.LP,” Uranus J. Ilm. Tek. Elektro, Sains dan Inform., vol. 2, no. 1, pp. 21–34, 2024, doi: 10.61132/uranus.v2i1.80.
[14] N. Eze and I. Eneh, “Using Failure Occurrence, Severity, Detection, and Risk Priority Number in Developing FMEA Worksheet in a Brewery for Failure Mitigation,” Int. J. Eng. Environ. Sci., vol. 5, no. 3, pp. 1–9, 2022, [Online]. Available: https://airjournal.org/ijees
[15] I. B. Bachtiar, M. Darul K., and M. Yusuf S., “Analisis Risiko Goliath Crane Galangan Kapal Menggunakan Fuzzy FMEA,” J. Teknol. Marit., vol. 7, no. 1, pp. 35–45, 2024, doi: 10.35991/jtm.v7i1.9.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Keisha Dinda Syamikha, Mega Cattleya Prameswari Annissaa Islami (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
