Evaluasi Desain Tower Truck Shipping Out Station dan Analisis Keselamatan Kerja Proses Penerpalan dengan Metode HIRADC Pada PT XYZ
Keywords:
HIRADC, Penerpalan, Keselamatan Kerja, Tower, Kecelakaan Kerja.Abstract
Tarpaulin work is work carried out at height to protect a product. Tarpaulin work is a high-risk activity if you are not equipped with the appropriate safety equipment. The risk of serious injury is high because of the height at which tarpaulin work is carried out. This research resulted in an evaluation of the Tower Truck Discharge Station, a new infrastructure to support safety in the tarpaulin process. Based on the results of data processing based on truck height variability, it is recommended that the ideal tower height of approximately 300 cm be established as a reference. With this tower height, the distance that workers have to cover when descending into the truck bed is reduced to only 14 cm, while the distance that workers have to cover when climbing onto the truck is approximately 18 cm. It was also found that when identifying and assessing hazards during the tarpaulin process, accidents caused by slippery steps on the truck bed were included in the low-risk category, although they still required vigilance. Factors such as climbing or descending high steps (2-3 metres), working at height, exposure to extreme weather conditions (heat, wind, rain) and exposure to dust or hazardous materials were placed in the medium risk category because they increase the potential for accidents. Meanwhile, the risk from slippery fertiliser piles is classified as high risk because it has the potential to cause fatal accidents, so serious precautions are needed.
References
[1] Mustaghfirin, Teknik Industri Analisa Perancangan Sistem Kerja, Kementrian Pendidikan & Kebudayaan Indonesia Press, 2015.
[2] P. W. M. I Made Sutajaya, “Ergonomi Dalam Pembelajaran Menunjang Profesionalisme Guru Di Era Global,” JPI (Jurnal Pendidik. Indones., vol. 5, no. 1, p. 82, 2016.
[3] M. Z. Ulhaq, I. M. Amhar, N. Husna, A. Syahrin, and A. Iqlima, “Peningkatan Pengetahuan Ergonomi Tentang Prinsip Prinsip Dalam Gerakan Di Sekolah SMAN 2 Bireuen Increasing,” Pap. Knowl. . Towar. a Media Hist. Doc., vol. 3, no. 1, pp. 12–26, 2020.
[4] A. Sarbiah, “Penerapan Pelaksanaan Keselamatan dan Kesehatan Kerja (K3) pada Karyawan,” Heal. Inf. J. Penelit., vol. 15, no. 2, pp. e1210–e1210, 2023.
[5] V. Suryan, A. N. Sari, D. Amalia, V. Septiani, and H. Febiyanti, “Peningkatan Keselamatan dan Kesehatan Kerja (K3) melalui Sosialisasi Alat Pelindung Diri (APD) kepada Pekerja Konstruksi (Lokasi: Renovasi Gedung Perpustakaan Politeknik Penerbangan Palembang),” Darmabakti J. Inov. Pengabdi. dalam Penerbangan, vol. 1, no. 1, pp. 30–37, 2020.
[6] R. D. Prasetyo and E. Widowati, “Implementasi Standar K3 Di Ketinggian Sebagai Upaya Pencegahan Kecelakaan Kerja Di Proyek Pembangunan Gedung X (Studi Kasus Proyek Pembangunan Gedung X Kota Semarang),” HIGEIA (Journal Public Heal. Res. Dev., vol. 6, no. 4, pp. 332–343, 2022.
[7] Kementerian Ketenagakerjaan Republik Indonesia, Retrieved from Satu Data Kemnaker, 15 Juli 2024. https://satudata.kemnaker.go.id/data/kumpulan-data/1881.
[8] M. R. Lazuardi, T. Sukwika, and K. Kholil, “Analisis Manajemen Risiko Keselamatan dan Kesehatan Kerja Menggunakan Metode HIRADC pada Departemen Assembly Listrik,” J. Appl. Manag. Res., vol. 2, no. 1, pp. 11–20, 2022.
[9] Radityazty Dahayu Nurhayati and Yayok Suryo Purnomo, “Analisis Risiko K3 dengan Metode HIRADC pada Industri Pengolahan Makanan Laut di Jawa Timur,” INSOLOGI J. Sains dan Teknol., vol. 2, no. 3, pp. 450–461, 2023.
[10] D. Mentari Ramadhania, Nazarwin Saputra, Dadang Herdiansyah, “Analisis Hazard Identification, Risk Assesment, Determining Control (Hiradc) Pada Aktivitas Kerja Di Ud Ridho Abadi Tangerang Selatan Tahun 2020,” Environ. Occup. Heal. Saf. J., vol. 2, no. 1, pp. 59–68, 2021.
[11] V. A. Fajar, K. Soeryodarundio, and M. Rifai, “Occupational Health & Safety Risk Analysis with HIRADC Method in Building Construction Project X,” Sustain. Civ. Build. Manag. Eng., vol. 1, no. 4, p. 9, 2024.
[12] T. Sukwika and H. D. Pranata, “Analisis Keselamatan dan Kesehatan Kerja Bidang Freight Forwader Menggunakan Metode HIRADC,” J. Tek., vol. 20, no. 1, pp. 1–13, 2022.
[13] A. I. Gutawa and Tranggono, “Revitalisasi Mobilitas: Pengoptimalan Sistem Penyeberangan JalanTerintegrasi dengan Metode Hazard Identification Risk Assesment andDetermining Control Pada PT XYZ,” Konstr. Publ. Ilmu Tek. Perenc. Tata Ruang dan Tek. Sipil, vol. 2, no. 1, pp. 87–98, 2024.
[14] D. A. Prasetyo and R. F. Pradistia, “Pemanfaatan Sensor Piezoelektrik Sebagai Penghasil Sumber Energi Dengan Tekanan Anak Tangga,” Emit. J. Tek. Elektro, vol. 22, no. 1, pp. 55–64, 2022.
[15] D. E. Wibowo, I. Wahyuni, A. D. Hastutiningsih, I. M. Nurshefa, and D. D. Rimbawati, “Occupational safety and health risk analysis using HIRARC and JSA methods in building projects construction,” AIP Conf. Proc., vol. 2629, no. 1, 2023.
[16] A. Mawardani and C. K. Herbawani, “Analisa Penerapan Hiradc Di Tempat Kerja Sebagai Upaya Pengendalian Risiko: a Literature Review,” PREPOTIF J. Kesehat. Masy., vol. 6, no. 1, pp. 316–322, 2022.
[17] A. Y. Kurniawan and F. Kurniawan, “Risk Management Related To Identifying Work Accidents in Loading and Unloading Container Activities At the Berlian Terminal Tanjung Perak Surabaya With the Hazard Identification Risk Assessment and Determining Control (Hiradc) Method,” Neutron, vol. 19, no. 2, pp. 26–32, 2020.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Muhammad Afif Ramadhan , Rusindiyanto (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
